"New Products"

Here are the new 4340 non-twist forged crankshafts from Ohio Crank. We've checked these cranks out and they are very good quality. More fine products from the great state of Ohio. We've done quite extensive testing on the dyno and track with these cranks. We recommend these for applications that are for 600-1400 HP. Of course you can use these on lower horsepower engine if you want too.

4340 forged 4.25 stroke with 3.00 main - BBC journal $ 625.00

4340 forged 4.50 stroke with 3.00 main - BBC journal $ 625.00 4340 forged 4.75 stroke with 3.00 main - BBC journal $ 625.00 4340 forged 4.21 stroke with 3.00 main - Pontiac journal $ 625.00

4340 forged 3.75 stroke with 3.00 main - Pontiac journal $ 625.00

4340 forged 4.25 stroke with 3.25 main - BBC journal $ 625.00

4340 forged 4.21 stroke with 3.25 main - Pontiac journal $ 625.00

$ 30.00 This is Tin Indian Performance's new Viton rear main seal. Designed for the best oil control that you can get in a seal. We carry both the 3" and 3.25". Works great for stock and aftermarket crankshafts and blocks. Color coded for for correct applications and fit.

3" Viton seal 3.25" Viton seal

These are the multi layer steel gaskets from Cometic. Just another Pontiac part made right here in Ohio. These are great for the one looking for either extra holding strength, thicker gaskets and bigger bores. The bigger bore sizes are are great for the MR-1 block. We have tested quite a few of them and can say they will hold up to over 1000 HP. These are the most popular gaskets we have in stock, thicker sizes can be custom ordered.

Cometic 4.200 bore x .040 thick $ 177.00

Cometic 4.200 bore x .051 thick $ 177.00

Cometic 4.200 bore x .060 thick $ 205.00

Cometic 4.250 bore x .040 thick $ 177.00

Cometic 4.250 bore x .051 thick $ 177.00

Cometic 4.250 bore x .060 thick $ 205.00

Cometic 4.300 bore x .040 thick $ 177.00

Cometic 4.300 bore x .051 thick $ 177.00

Cometic 4.300 bore x .060 thick $ 205.00

Cometic 4.380 bore x .040 thick $ 177.00

Cometic 4.380 bore x .051 thick $ 177.00

Cometic 4.380 bore x .060 thick $ 205.00

$ 60.00 These are nice CNC 3/8" thick header flanges made buy Tin Indian Performance. Designed for round port heads like the KRE High Port, Edelbrock and Ram Air II & IV. They come in 2 primary tube sizes 2" and 2 1/8".

2" flange

2 1/8" flange

$ 55.00 ea. Here is our lastest part that we have been working on! A stock replacement aluminum oil filter housing. This piece is designed for the stock oil filter and has the angle to pull the filter closer to the block for header clearance. Made from 356-T6 alum. for strength just like our cylinder heads. Will fit the MR-1 and stock blocks.

$ 35.00 This is our new billet distributor hold down made from 6061T-6 Aluminum. This is just another one of our fine products that we have designed on our in house CNC machines. Will fit both stock blocks and MR-1 aftermarket block.

$ 20.00 Here's a Tri-Power fuel pump plate that we came up with!!!!

$ 18.00 Here are some new valve cover gaskets! These are made of a hard rubber material with a steel inner core. They are very durable and seem to work very well with all valve covers! They last a lot longer over time then other gaskets that are made of cork!

$ 6.50 $ 25.00 Some more great products from Tin Indian Performance! Those old oil pan plates that get lost from engine tear downs are now available. These two plate go in the back corner of the oil pan rail. We also have a more affordable cam thrust plate made by Tin Indian Performance that includes the bolts!

$ 165.00 New Pontiac crank mandrel for a vaccum pump setups from Tin Indian Performance! Bolts to either stock 4 bolt or 3 bolt Chevy stile dampers! Very nice setup with adjustable spacers to accomdate every engine setup for belt alignment. Standard setup comes compelete with 3" pulley and bolts.

Here is the Moroso pump bracket made by Tin Indian Performance. This bracket is designed for the 3 and 4 vane Moroso Vac Pump to bolt right to (any) Pontiac cylinder head that has the standard accesory bolt holes on the end of the head.

$ 52.50 Tip pump bracket

$ 229.00 Here is the new Hurricane(Tomahawk) intake manifold from Professional Products. This single plane intake setup for std Holley/Demon carbs and Q-jets. Designed to fit heads with an airflow range of 260-330 cfm. As time permits we will be testing this manifold on many of the different combos that we have had good success with to see how it works compared to them. We feel there are many applications that this intake is going to help make power. $ 289.00 polished

$ 20.00 ea. Some more fuel pump block plates. First & Second generation Firebird plus indian head logo.

$ 60.00 $ 155.00 Here are some new dampers from Professional Products. Very nicely made with white lettered timing marks from 0-60 degrees. The stock damper is perfect for the stock to mild performance engines. The SFI unit is great for mild to high performance engines.

$ 18.95 It's here, Jim Hand's street performance Pontiac book. Lots of technical goodies, info, new products and many different engine combos to look over. Get your's now, so you can show up your Chevy buddies the next time your paired off at the stop lights. In stock and ready to ship!

$ 35.00 This is another fine product that we made with new CNC machine! It's machined out of 6061T-6 Aluminum. Setup for remote filtering of oil. Has been tapped with 1/2" pipe tap. Perfect fit for Aluminum AN fittings or hyd. hose.

$ 20.00 This is our own fuel pump block off plate made on our new CNC machine! It's machined out of 6061T-6 Aluminum. A perfect match for any Pontiac engine that will be using an electric fuel pump.

$ 1695.00 This is a complete rotating Eagle crank kit prepared by KRE. Kit's come with crank, pistons, rods, bearings, rings and are balanced. Pricing starts with flat top pistons!!! Kit's come in three different cranks.

3" main 4.25 stroke BBC Eagle 6.800 rods, SRP pistons, FM bearings and Speed Pro rings 3 1/4" main 4.25 stroke BBC Eagle 6.800 rods, SRP pistons, FM bearings and Speed pro rings 3 1/4" main 4.21 stroke CAT 6.625 rods, SRP pistons, FM bearings and Speed Pro rings Call or E-mail us for prices on upgrading to Ross pistons (FT, dished or dome), Crower rods and Total seal gapless rings!

$ 315.00 These are our custom made sheet metal valve covers. Ridged in design but still light weight. It has a 3/8 thick bottom rail for gasket sealing.

$ 5.00 This washer relaces the camshaft eccentric. We mostly use these on full race engines.

$ 25.00 This piece is CNC laser cut from 1/4" plate steel. Perfect for using on the new MR-1 blocks. Sure beats digging out old rusty beat up ones!

$ 42.00 This is a 150 piece stainless steel bolt kit. It comes in hex headed bolts. It's inexpensive and works very nice for finishing off an engine build.

SCE is making many different gaskets for Pontiacs now. 2.320 * 1.180 Intake gasket.$ 11.00

Round port head copper exhaust gaskets are $ 32.00.
5/16 valve cover gaskets are$ 18.00

2.250 * 1.150 Trim to fit intake gasket$ 11.00

This starter is one of the best I've seen. It has 200 ft.lbs rating with a 4.41 gear reduction. It only weighs 8.5 lbs. It comes with a heat soak resistant housing and an aluminum billet mounting surface. This starter is for 12 to 1 compression engines and higher. $ 215.00
This is Power Masters street starter. Designed for 12 to 1 and lower compression engines. It's rated at 180 ft.lbs and has a multi positioning mounting surface. $ 180.00